60000PSI Small portable water jet cutter
SPECIFICATIONS FOR WATER JET CUTTING MACHINE
HP hydraulic intensifier pump
Single row water filtration system (5Micron, 1micron, series)
Manual voltage regulation
Over-pressure automatic shutdown and under-voltage automatic protection function. A10V071 automatic variable oil pump and Schneider electrical components with high performance.
Advantages of the WAMIT servo direct drive pump:
B: Environmental protection: the use of servo direct drive, no hydraulic system, with self-cooling function. As we all know, hydraulic The hydraulic intensifier system must be filled with 110L of anti-wear hydraulic oil to work, and the heat generated by the hydraulic oil is also cooled by the oil cooler. The direct drive pump is completely free of hydraulic oil and cooling system.
C: High efficiency: Direct drive pump provides a higher pressure output ratio, cutting speed is 20 to 50% faster than the same equipment in the market.
E: Low noise: almost no noise when working.
F: Small weight: The total weight of the direct drive pump is less than 600kg, and the movement is flexible. The weight of the hydraulic intensifier pump is 1000kg.
G: Beautiful appearance: The structure is reasonable in design and beautiful in appearance, because the direct drive pump does not have a hydraulic system, Thereby avoiding the leakage of the hydraulic oil (the hydraulic seal will be damaged for a long time use, causing the hydraulic oil to leak), eliminates the contamination of equipment by oil stains.
• Support for DXF files.
• Support forward and reverse processing functions.
• Uniform speed control function.
• Two modes of segmentation and smooth machining.
• Automatic processing with small arc speed.
• Coordinate recovery function after power off.
• Double lift speed parameter function.
• With cycle processing.
• Convenient pause to continue and start machining in any segment.
• Free time delay setting.
• Apply SIEMENS PLC instead of relay, buttons are Schneider.
• High-precision sensors alert operators when they need to replenish sand
• Safety relief valve
• Working pressure: 0.2-0.3MPa
• Water separator
No need electronic control, simple operation, reliable, maintenance-free.
Can supply the cutting sand quantity .
Need less than 0.2Mpa compressed gas pressure.
Provide sand storage for the water jet cutter and automatically transfer the sand to the sand bucket.
Can increase the automation of the equipment and reduce the labor intensity of the operator.
Shot blasting and powder coating
Remove impurities such as surface oxide scale to improve appearance quality.it can improve the fatigue fracture resistance of materials, prevent fatigue failure, plastic deformation and brittle fracture, and improve fatigue life.
Test the straightness and parallelism of linear guide rail with precision measuring instruments.
Guaranteed higher precision when the equipment is running after the linear guide rail is installed.
Calibrating equipment precision with a laser interferometer.guaranteed more accurate cutting precision.
Servo direct drive pump
Hydraulic intensifier pump
Carbon steel plate
This product is a new type of sand removal equipment independently developed by Shandong Womai CNC Technology Co., Ltd. Simple operation, high sand removal efficiency and almost no maintenance. The birth of the WAMI Auto desanding system for water jet cutting machinery solved the problem of clearing waste sand for water jet users all over the world.
Features of WAMI water jet cutting machinery auto desanding system:
The sand removing device can perform sand removing work while the water jet machine is working. The equipment has improved the traditional sand removal operation (the machine must be shut down, the water and sand of the tank are cleaned out and the water is filled again), which has gained valuable time for normal work.
B: Simple operation, complete sand removal and fast sand removal.
It takes only 5 steps to complete the sand removal work: 1. The equipment is in position → 2. the air source is switched → 3. The sand suction head is placed in the water tank → 4, open the air source switch to remove sand → 5, the sand chamber is full of shutdown and dump the waste sand. Sand removal rate of the equipment More than 90%.
C: Large capacity.
The device has a diameter of 630 (720) mm, a height of 2.1 M, and a sand removal of up to 460 (610) L. For example, a water tank of 2 m * 3 m can be used continuously after removing 3-4 cans at a time.
D: Thick steel plate, perfect hydraulic system.
The equipment tank is made of 8mm thick steel plate, and an advanced water sand separation system is integrated inside the tank. Base is 20mm thick steel plate for durability. The switch base uses a manual hydraulic system and is equipped with safety bolts to make the base switch and seal become
simple, safe and convenient.
E: Powerful and stable.
The equipment uses an advanced pneumatic diaphragm pump to generate a constant flow of high-pressure water under the drive of high-pressure gas.
Sand removal provides powerful power.
F: energy saving.
The entire sand removal process of the equipment does not lose water in the water tank and does not cause waste of water resources.
G: Mobile flexibility.
The device is equipped with a ear holder for forklift fork picking, which is convenient to move, and one sand removing device can be used for multiple water jets.
1. Are you manufacturer or trading company?
We are manufacturer of water jet cutting machine in JINAN city, Shandong, China.
2. What kind of material does your water jet cutting machine can cut?
There are plenty materials our water jet cutting machine can cut, such as stone, ceramic, quartz, glass, foam, plastic, rubber, copper, brass, aluminum, mild steel, pre-hardened steel, titanium, inconel and cast alloy.
3. What’s your CNC water jet cutting machine’s max. cutting thickness?
Generally speaking, if cut steel the max thickness of our water jet cutting machine can be up to 240mm, but we suggest cut no more than 150mm for smooth cutting. Now our Z axis distance is 170mm, we can customize for customers. Regular thickness please refer to: Marble is 0-120mm; granite is 0-110mm; tiles are 0-40mm; glass and mosaic is 0-80mm; steel, stainless steel, copper is 0-60mm; aluminum is 0-80mm; plastic, acrylic, foam is 0-200mm.
4. How we supply after-service?
Some countries we have after-service department, we will provide local service, if have no local service, we will arrange engineer for overseas installation and training. The installation and training time is generally 7-10 days. And we also can provide installation videos.
5. What’s your delivery time?
Generally speaking is 30 days. if have stock, 7-15 days.